PID Control of Planar Nonlinear Uncertain Systems in the Presence of Actuator Saturation

This paper investigates PID control design for a class of planar nonlinear uncertain systems in the presence of actuator saturation. Based on the bounds on the growth rates of the nonlinear uncertain function in the system model, the system is placed in a linear differential inclusion. Each vertex system of the linear differential inclusion is a linear system subject to actuator saturation. By placing the saturated PID control into a convex hull formed by the PID controller and an auxiliary linear feedback law, we establish conditions under which an ellipsoid is contractively invariant and hence is an estimate of the domain of attraction of the equilibrium point of the closed-loop system. The equilibrium point corresponds to the desired set point for the system output. Thus, the location of the equilibrium point and the size of the domain of attraction determine, respectively, the set point that the output can achieve and the range of initial conditions from which this set point can be reached. Based on these conditions, the feasible set points can be determined and the design of the PID control law that stabilizes the nonlinear uncertain system at a feasible set point with a large domain of attraction can then be formulated and solved as a constrained optimization problem with constraints in the form of linear matrix inequalities (LMIs). Application of the proposed design to a magnetic suspension system illustrates the design process and the performance of the resulting PID control law.      

基于软件校准的短波发射机功率控制系统设计

短波发射机功率稳定一直是通信领域致力改善的重点问题,短波发射机功率不稳定会直接影响无线电通信质量,造成通信失真、表达不清晰等问题。针对上述问题,基于软件校准设计短波发射机功率控制系统。该系统借鉴MVC设计模式搭建系统数据库层、业务逻辑层、控制层以及界面显示层基础框架；将功率计与短波发射机相连,实时采集工作状态下的短波发射机功率数据,通过信号处理器实施处理后并存储,借鉴传输元件,将数据发送到控制器,通过控制器校准短波发射机功率与预期之间的偏差,以偏差量为输入,利用改进PID运算得出控制量,生成控制命令,通过输入输出信号接口板输出命令,控制驱动装置调节短波发射机运行参数,实现功率控制。结果表明：与 控制系统、自动调谐系统应用相比较,在所设计系统应用控制下,100s内短波发射机的功率变化曲线与预期曲线之间的拟合优度指数更大,更接近1,优于对比系统,说明相比于对比系统。本系统控制表现更好,更能维持短波发射机功率稳定,达到了研究目标。     

基于多自由度气动机械手位置伺服系统稳定性控制研究

基于传统易碎薄板机械手位置伺服控制系统稳定性低、自动化分拣效率低等不足,设计了一种基于笛卡尔坐标式的气动码垛机器手和位置伺服稳定性控制系统。首先,设计并介绍笛卡尔坐标式码垛机械手的基本组成结构,对机械手末端吸盘气动回路控制系统进行设计和分析;然后分别对机械手X、Y、Z三个方向的伺服电机控制原理进行分析并设计了一种位置伺服系统的前馈自适应控制算法;最后,将传统位置闭环PID算法和前馈自适应控制算法进行位置跟踪稳定性对比试验。实验结果表明该笛卡尔坐标式的气动码垛机器手和位置伺服稳定性控制系统设计合理,满足实际生产要求。     

基于模糊多模型的堆芯功率控制

传统的堆芯功率PID控制器是基于单一功率水平处的堆芯局部模型设计的，难以准确描述整个堆芯功率水平范围的控制。因此，本文基于5个不同功率水平下的传递函数模型，通过三角隶属度函数加权，建立堆芯模糊多模型，并依据该模型设计堆芯功率模糊PID控制。以TMI型压水堆堆芯为对象，开展不同初始功率水平下的堆芯功率跟踪、堆芯进口温度扰动的控制仿真。结果表明，基于模糊多模型设计的堆芯功率模糊PID控制器可实现对堆芯功率的良好控制。     

某两自由度弹药提升装置的建模、实验及仿真研究

弹药自动装填系统的研究已经成为火炮武器平台中机械系统设计的关键和难点,基于一种两自由度弹药提升装置,并根据该装置的工作原理构造数学模型,搭建实验平台,建立PID控制回路,同时创建该模型的虚拟样机模型,使用动力学仿真软件Recurdyn和Matlab/Simulink进行联合仿真,并通过实验与仿真的数据进行对比,验证该装置的可行性和所采用控制的有效性。     

Bulging in incremental sheet forming of cold bonded multi-layered Cu clad sheet: Influence of forming conditions and bending

Bulge is a defect that causes geometrical inaccuracy and premature failure in the innovative incremental sheet forming (ISF) process. This study has two-fold objectives: (1) knowing the bulging behavior of a Cu clad tri-layered steel sheet as a function of forming conditions, and (2) analyzing the bending effect on bulging in an attempt to identify the associated mechanism. A series of ISF tests and bending analysis are performed to realize these objectives. From the cause-effect analysis, it is found that bulge formation in the layered sheet is sensitive to forming conditions in a way that bulging can be minimized utilizing annealed material and performing ISF with larger tool diameter and step size. The bending under tension analysis reveals that the formation of bulge is an outgrowth of bending moment that the forming tool applies on the sheet during ISF. Furthermore, the magnitude of bending moment depending upon the forming conditions varies from 0.046 to 10.24 N·m/m and causes a corresponding change in the mean bulge height from 0.07 to 0.91 mm. The bending moment governs bulging in layered sheet through a linear law. These findings lead to a conclusion that the bulge defect can be overcome by controlling the bending moment and the formula proposed can be helpful in this regards.     

基于ＰＩＤ控制算法的直流微网容错控制方法研究

构建直流微网容错控制对象模型，调节直流微电网的输出回路参数；以输出功率、直流微网的 参考电压、弱电网下系统惯性响应特征等为约束参量，构建直流微网容错控制目标函数，在不同电网强度下 进行直流微网容错控制的参数自整定性调节，采用无功环比例积分控制方法进行直流微网容错寻优分析， 建立模糊 ＰＩＤ控制模型，采用变结构的模糊 ＰＩＤ控制方法进行直流微网容错控制过程中的自适应加权学习 和误差反馈调节，实现直流微网容错控制改进设计。仿真结果表明，采用该方法进行直流微网控制的容错 性能较好，输出稳定性较强，具有较好的直流微网输出增益。     

浅谈焦炉煤气鼓风机高压变频调速控制系统的设计

本文对焦炉煤气加压控制系统进行了分析，在焦炉煤气加压机控制系统中运用变频调速技术对其进行改造，从而实现煤气加压机运转的自动调节，有效地稳定了焦炉煤气母管压力，保证了安全运行，并且达到节约能源的效果。解决了两台鼓风机并列运行，靠调节回流阀无法实现压力恒定这个始终困扰焦炉生产的难题。     

浅谈在多节目码流复用与解复用中PID码的作用

文章简要阐述了PID码在多节目码流的复用与解复用中所起的作用。并运用PID码的原理来解释和解决在实际工作中碰到的PID码问题。